Fire Solutions

R5A-RF WCP Wireless Make System Sensor, 865-867 Mhz, <25mW e.r.p., 4 CR123A 3V Batteries, EN54-25 (RFsanato)EN54-11, 134 L109 W99 H

RESPONSE INDICATOR MODEL NO RI/007C, Response Indicators are connected to Fire Detectors to indicate quickly the source of analarm signal from detectors, which are not easily accessible or visibleHoneywell Remote Indicators provide visual indication of an alarm on a concealedconventional or addressable DetectorMultiple detectors can be connected to a single RI, but for individual Fire Detector alarmidentification it is recommended to connect single detector with a single RI.• Rugged / Industrial Design• Flush Mounting, Wall mounting• High bright LED (Wide Viewing Angle)• Operating voltage - 5 to 28V DC• Current - >15mA @ 12V DC• Life upto 100000 Hrs.

Vane-type waterflow detectors shall be installed on system piping as designated on the drawing and/or as specified herein. Detectors shall mount on anyclear pipe span of the appropriate nominal size, either a vertical upflow or horizontal run, at least 6˝ from any fittings that may change water direction,flow rate, or pipe diameter or no closer than 24˝ from a valve or drain. Detectors shall have a sensitivity in the range of 4 to 10 gallons per minute and astatic pressure rating of 450 psi* for 2˝ – 8˝ pipes. The detector shall respond to waterflow in the specified direction after a preset time delay that is fieldadjustable. The delay mechanism shall be a sealed mechanical pneumatic unit with visual indication of actuation. The actuation mechanism shall includea polyethylene vane inserted through a hole in the pipe and connected by a mechanical linkage to the delay mechanism. Outputs shall consist of dualSPDT switches (Form C contacts). Two conduit entrances for standard fittings of commonly used electrical conduit shall be provided on the detectors.A grounding provision is provided. Unless noted, enclosures shall be NEMA 4 listed by Underwriters Laboratories Inc. All detectors shall be listed byUnderwriters Laboratories Inc. for indoor or outdoor use.

Water Flow Switch 3'' Inch make System Sensor, Vane-type waterflow detectors shall be installed on system piping as designated on the drawing and/or as specified herein. Detectors shall mount on anyclear pipe span of the appropriate nominal size, either a vertical upflow or horizontal run, at least 6˝ from any fittings that may change water direction,flow rate, or pipe diameter or no closer than 24˝ from a valve or drain. Detectors shall have a sensitivity in the range of 4 to 10 gallons per minute and astatic pressure rating of 450 psi* for 2˝ – 8˝ pipes. The detector shall respond to waterflow in the specified direction after a preset time delay that is fieldadjustable. The delay mechanism shall be a sealed mechanical pneumatic unit with visual indication of actuation. The actuation mechanism shall includea polyethylene vane inserted through a hole in the pipe and connected by a mechanical linkage to the delay mechanism. Outputs shall consist of dualSPDT switches (Form C contacts). Two conduit entrances for standard fittings of commonly used electrical conduit shall be provided on the detectors.A grounding provision is provided. Unless noted, enclosures shall be NEMA 4 listed by Underwriters Laboratories Inc. All detectors shall be listed byUnderwriters Laboratories Inc. for indoor or outdoor use.

We are a remarkable entity in this domain, engaged in offering a qualitative assortment of Honeywell HN-WM06 Wall Mounted Speaker.

22051E-RF-26 Photo Detector Wireless Make System Sensor, The new wireless platform is powered by robust meshnetwork technology providing up to two communicationpaths to each wireless device. This makes the network highlyreliable, protecting against broken communication links.Mesh network technology enables flexible and economicinstallations in a wide variety of building footprints.

Convenional Manual Call Point MCP2A/R470FF/01 Make System Sensor, Conv. MCP, Red, with LED ,470 Ohm, W/O Back Box, India, The MCP2A Product version is supplied with both a resistor and normally open, clean contactelectrical options. These options are simpily utilised by attaching the terminal block to therequired connection in the back of the MCP product. A variety of resistsor values are availableby request, with 470Ω offered as standard.

The 5351/E thermal detector forms part of the Series 300 range of conventional detectors. This rangeof detectors has been produced using the latest in manufacturing and design techniques, pushing outthe boundaries of existing conventional detector technology., Low profile design• Low current draw• Backward compatible with Series 100 detector range of bases• Wide operating voltage 8 to 30VDC• Bi-colour LED detector status indicator• Range of detector bases available• Tested and approved to EN54 –5:2000 Class A1R (Amendment 1)• Extended warranty

B501RF Detector Base Wireless Make System Sensor, The Morley Addressable Wireless Fire Detection System is anextension of the Series 200 product range. It features the sameclass leading device design, detection performance, false alarmimmunity and system functionality. Wireless devices can beseamlessly integrated into existing panels supporting Series 200protocols, giving the fire system the flexibility to be easily extended

Being a leader in the industry, we are engaged in offering a qualitative range of Honeywell HN-CL06 Ceiling Speaker to our customers.

MI-GATE Gateway Wireless Make System Sensor , 865-867 MHz, CommunicationLine Supply Range: 24VStand by Current: 230μA, EN54-25 (RF)EN54-18EN54-17, 42mm(with B501AP base)